• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are long-lasting, durable and easy to maintain. They do not rot or rust like timber and aluminum.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will reduce costly repairs and improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home and even be fatal. It is important to make sure that your windows are in good working order.

Single-pane windows are fairly simple to replace and will usually fit into the old frames very easily. However, if you have double pane windows that are anchored by internal beading it will be more difficult to remove the old panes and put in new ones. In this case you'll need source some plastic spacers that will assist the new pane to fit properly into the frame of the window.

If you're planning to attempt to remove the glass panes yourself it is crucial to wear the proper safety gear such as gloves that are thick and eye protection. You should also lay down a drop cloth before you begin working on the window panes so that any shards fall onto the fabric and not onto the floor, where they could be trampled under.

Once the glass is removed, it's a good idea to cover the gap with clear packaging tape or duct tape to prevent water and drafts from entering the home until a professional comes out and repair the window. This will also act as a barrier that will prevent any intruders to gain access to your home. If the gap between the window and the door is substantial, you may need to consider an alarm system that has an opening. This will give you the best of both.

2. Sagging

uPVC windows and doors are a cost-effective energy-efficient, durable and long-lasting alternative to timber windows with sash. As time passes, they may be affected by a variety of issues such as sagging. A sagging window in uPVC can cause issues with light, draughts, and even security. It's important to take action immediately if you discover that your uPVC windows are sagging.

To fix a sagging window you can try repositioning the hinges. First, you'll need to open the windows so you can get at the frame. Then, remove both the hinges at the top and bottom using a screwdriver and adjust them clockwise or counter-clockwise. Once you've adjusted the hinges, close the window and test it for fitting. If you're satisfied with the fit of your window, you can tighten screws to hold them in the right position.

If you cannot reposition the hinges, you may need to replace the seal. Over time, rubber seals lose their elasticity and dry out and cause their tightness to decrease. It is crucial to replace your seal as quickly as you can to ensure that your uPVC window watertight and draughtproof.

uPVC handles may also become loose. This is usually due to screws that have become undone over time, but it can be caused by the handle mechanism wears out. It's relatively simple to fix a loose uPVC handle. First, you'll need to shut the window and then perform an experiment fitting. The corner joints of the sash must be aligned with the casing joint. If it isn't then you can make use of a screwdriver to loosen the handle and then reverse the mechanism back into the position it was in.

3. Water Leaks

It is essential to take action if awake each day to discover mouldy walls and floors that are wet. The leaks of water from windows do not only lead to the destruction of your home's structure but also hinder your efforts to regulate the temperature in your home. The most common reason for leaks in uPVC windows is that the sealant surrounding the frame has been damaged or not present.

This is an easy fix that can be done by any DIYer who is competent. Based on the severity of the problem the caulking used previously may need to be removed before a fresh layer can be put on. It is important to keep in mind that when it comes to uPVC window repairs you should avoid the temptation to "over-caulk in order to make the area more difficult to clean and can reduce your energy efficiency.

Check that any drainage holes are free of debris inside them and ensure that the sill pan is properly angled to drain away from the window. In more serious situations, you may have to replace the window.

Moldy sills and rotten ones are also signs of water leakage. This is a fungus that thrives in damp conditions and can quickly spread across the house.

It is also important to keep in mind that if the leakage is coming from between the glass of your double-glazed windows it may be more likely to be a problem with the glass seal, rather than the frame or sliding. It is also possible to be repaired by a uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault when your uPVC window is difficult to open or if it opens in a breeze. They can be repaired by any DIYer who is skilled and can usually be done within a few minutes.

Most households in the UK will have top-hung or side-hung uPVC windows that are hinged and, like all mechanical parts, they can wear down over time. It's very simple to change the hinges on a window but it's much simpler if you have someone to help you hold the frame.

Verify that the uPVC hinges are closed and open in the right direction. You can do this by checking for the arrows on each hinge, this shows which way the window should be opened.

The issue could be caused by opening the window incorrectly or a faulty installation at the factory. Sending us a photo via our website will often resolve the problem. We are more than happy to give advice.

It is also important to lubricate the hinges regularly. This can be done by applying an oil that is light in nature to the hinges. We recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can help the window operate and close more smoothly. It can also reduce the risk of a window repairs near me sticking and help prevent corrosion. Ideally, you should do this once a year. WD40 and other solvent-based lubricants are not recommended as they can damage the parts of your uPVC window.

5. Draughts

Draughts in windows made of upvc can be caused by a few different factors. The hinges, also due to wear and tear can become misaligned, this can cause gaps to develop between the sash and the frame. They can be repaired by giving them a good clean, but when they're beyond repair, it may be necessary to have them realigned or replaced. In addition, the interlock could be misaligned. This is located on the hinge side and could require to be cleaned. In certain instances it might be necessary to replace them.

The next common reason for draughts is window repair seals, these are susceptible to being worn out or damaged over time, and allow air to escape through the gaps. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity lenses. This will help control indoor temperatures and decrease the risk of draughts.

Another, and most effective ways to cut down on drafts is to use an draught excluder. These are typically fabric tubes filled with some sort of filler and can be put on top of your windowsill. These will help to stop cold air from entering and keep your home warm and cozy!

With a little regular maintenance and repairs your windows made of upvc will continue to provide a great level of insulation and security for your home. It is crucial to keep in mind that all windows eventually wear out and it may be more cost-effective to simply replace them than to repair them. If you have any problems with your window made of upvc, it's best to consult an expert immediately.