• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to repair ignition lock cylinder (top article) an Ignition Lock Cylinder

If your car's key isn't turning, it's time to change the ignition lock cylinder. The lock cylinder is a tumbler made of mechanical that your key can slide into, in contrast to the switch, which is an electrical component of the ignition system.

Over time over time, these "wafer" tumblers wear out or break. The use of WD-40 or graphite could temporarily fix the problem but replacement is the only way to fix it permanently.

Removing the Steering Column

Modern cars do not have steering column locks. They use keys to start the vehicle by pressing and rotating an electronic switch located in the dashboard panel. This newer method is simpler and more effective than the older lock cylinder method. Certain older vehicles still use the traditional lock cylinder. If this component fails, it could be required to replace it to allow the car to start. This is not an activity for the novice and is best left to a professional.

Using a screwdriver, remove the fasteners holding the trim panels covering the lower and upper parts of the steering column. This will give you access to the area surrounding the steering column.

On the side of the steering column that is closest to the driver, you'll notice an Allen head bolt that pins the wiper/signal assembly in place. Unscrew this bolt and set it aside. Based on the year of your car, you might have three or four small flat head screws that secure the plastic cover that covers the turn signal switch. Remove these screws and set them aside.

To access the lock cylinder, you'll have to take off the signal/wiper assembly. You can either make use of a specific tool to remove it or ghetto it with an object of metal, such as a cold-chisel. A locksmith will also be equipped with a shear bolt removal kit.

If the key can't be put into the ignition switch, it's likely that the lock cylinder is stuck. You can try inserting the key and moving it to the ACC position to press the lock cylinder pin, or you can contact an expert locksmith for assistance.

A locksmith will be able to make use of a shear cylinder removal tool or they can cut the pin from the lock cylinder using a torch and then shave it to remove it from the cylinder. They will be able to replace the cylinder's keys to match your current keys and will save you the cost of buying a new ignition cylinder.

Replacing the Ignition Cylinder

The ignition Cylinder is the mechanical cylinder which houses and locks your car's key. The cylinder "reads" the anti-theft code and then fits your key to turn on or off your car. As time passes the cylinder wears out. It can also break or become bent. If this happens, the cylinder will require replacement to allow your car ignition locked to begin.

Signs of a damaged or worn cylinder include problems with turning the key, or the ignition switch not moving into the ACC or RUN position, or with a warning light appearing on the dashboard. If you have an extra key, use it inside the lock. You may be able to finesse the cylinder with some graphite or WD-40. However, this method is only effective for a limited time.

Replace the ignition cylinder if have an alternative key. Follow the steps above to install the new ignition cylinder. Install the new ignition cylinder by making sure that it is properly fitted into the steering-column tube flange and aligned with keyway on the shroud. Consult your car's manual or an expert to ensure that the cylinder is properly aligned.

After the cylinder is installed then turn the ignition key to ACC or RUN. You should hear a click confirm that the ignition switch has been fully seated in the cylinder. If your vehicle has an anti-theft device, you will need to follow the anti-theft relearn process to programme the new ignition cylinder into your key.

Some experts suggest having a professional replace the ignition cylinder since it is typically necessary to disable the airbag inside the steering column in order to access the cylinder. Furthermore, the replacement will likely involve taking off and replacing the ignition and steering wheel covers. This is why it's best to leave this job to an experienced mechanic. They'll be able to take off the cover for your steering wheel and install a new ignition locking cylinder in your car. They'll also be able to make sure that the ignition lock cylinder has been programmed with your key and that it starts correctly when you insert it.

Installing the Ignition Cylinder

Even though cylinders for ignition locks are no longer as important in modern cars due to remote start and push-tostart technology, older cars still make use of these cylinders. If you're having trouble starting your car or if the ignition switch is stuck, it could be an issue with the ignition cylinder. It's relatively simple to replace your car's ignition lock cylinder and fix ignition switch the issue.

The ignition cylinder is the mechanical portion of the system that slides into the ignition switch in your car and supplies power to the rest of the engine. While many people confuse the term "ignition switch" with the ignition cylinder, they're two distinct components. The switch is an electrical device that connects to your car's computer system to send signals to start the engine when you turn the ignition key.

The ignition lock cylinders have pins that move upwards and downwards to let your key slide into and rotate within the cylinder. Every movement of the cylinder and key creates a small amount of friction that helps keep the key in place, but in time, these tiny movements can cause the wafer tumblers to wear down. When the tumblers are worn down, your car's key will not be able to slide into or turn the cylinder.

A damaged ignition cylinder typically the first sign of trouble in the majority of vehicles. The key can also get stuck and be difficult to insert into or out of the ignition lock cylinder. These are indicators that you need to replace your ignition lock cylinder as soon as possible.

Replacing the ignition cylinder on your vehicle isn't difficult, but it's an undertaking that should be completed by a skilled do-it-yourselfer only when you're confident enough to follow the proper procedure for your specific brand and model of vehicle. A complete repair manual for your car will help you get the task done quickly and accurately. If you're not comfortable installing the ignition cylinder on your own You can let one of our ASE-certified mobile mechanics do the work for you at a time and location.

Test the Ignition Cylinder

The ignition lock cylinder, also referred to as the ignition lock cylinder, is a mechanical device that is fitted to your key to allow it to turn and start your car. It is inserted into the ignition switch that locks the ignition, and reads the anti-theft codes to allow key turning. The ignition lock cylinder can wear out and eventually fail. This can cause problems with the power of your vehicle or make it difficult to remove and insert keys.

The most common signs that a car's lock cylinder is about fail is difficulty starting your vehicle or finding places where the key gets stuck when you attempt to turn it. These issues usually indicate that the cylinder is worn down and requires replacement. You may even see an alert light flashing on your dashboard, signalling an imminent failure.

As the cylinder ages it may be damaged by corrosion or simply wear and wear and. This could cause the pins and tumblers made of wafer to wear out, damage or even break, which can stop your car's ignition from functioning. In certain instances the ignition may work if you jostle it in different directions however this is a dangerous indicator that something is wrong.

You can test your ignition cylinder to determine whether it's worn-out or if the key is bent or damaged. If you have a multimeter, you could probe the module's red wire connection and the battery terminal of the ignition coil to determine if there's any voltage. If you don't see any or no voltage, then the switch and module probably need to be replaced.

Replacing the ignition cylinder typically costs $200 to $300, and it's usually best to hire a professional mechanic perform the job. The process is complicated by the fact that you might need to remove other components to access the van ignition repair cylinder, including the steering column. The replacement procedure may also require you to deactivate the airbag system, and then reprogram your key in order to work with the new ignition cylinder. This is usually handled by an authorized dealer. However, you can do it yourself if have the right tools and instructions.